Jump to content

jman

Krayt Clan Members
  • Content count

    14
  • Joined

  • Last visited

Community Reputation

0 Neutral

About jman

  • Rank
    Member
  • Birthday June 29

Profile Information

  • Gender
    Male

501st Information

  • 501st ID
    20629
  • Name
    J. Calip
  1. Troop Name: Make A Wish - Sending to WDW (Jace) Troop Date: 10/27/17 Troop Location: San Diego, CA ID: DZ-20629 forum alias: jman
  2. Troop Name: Buddy Walk @ NTC (Down Syndrome) Troop Date: 10/22/17 Troop Location: San Diego, CA ID: DZ-20629 forum alias: jman
  3. Troop Name: Mike MS Bay to Bay Ride - Torrey Pines Troop Date: 10/22/17 Troop Location: San Diego, CA ID: DZ-20629 forum alias: jman
  4. Troop Name: Poway Library Cosplay After Hours Party, Costume Contest Judging Troop Date: 10/20/17 Troop Location: San Diego, CA ID: DZ-20629 forum alias: jman
  5. Troop Name: Autism Walk - Liberty Station Troop Date: 9/30/17 Troop Location: San Diego, CA ID: DZ-20629 forum alias: jman
  6. Troop Name: Mark Hamill Street Naming Troop Date: 7/30/17 Troop Location: San Diego, CA ID: DZ-20629 forum alias: jman
  7. Troop Name: Ruben H. Fleet Cosplay Night Troop Date: 7/28/17 Location: Balboa Park, San Diego, CA ID: DZ-20629 forum alias: jman
  8. Sorry for the delay in responding... each time I remembered, I was not at a computer to check. It comes up for me as a jpeg (.jpg). Did you try right clicking it and saving the linked file onto your drive? That is one way to try it which works for me. Nonetheless, I will see if I can PM you a copy of the file.
  9. The template provided in this thread (see page 1, March 21, 2014 entry) comes up fine for me. Did you try that one?
  10. This thread is fantastic. Thanks Arcturus for putting this together. I have a question for anyone that has used the template as currently documented on the first page. Assuming that my print out of the template is accurate, I get 6" across the bottom section, with a height of 4.5" on that bottom section. The upper flap section being roughly 2.5" across/wide. That upper section essentially dictates what the width of the pouch will be. According to the write up, the desire is to get a 3.5" by 5.5" pouch. With the dimensions of the template as is, I don't see how you can get a 3.5 X 5.5 inch pouch dimensions? Maybe 3x5, but that pushing it. I cut a piece of leather to these dimensions and I do not get anywhere close to those dimensions. I have modified the dimensions a tie bit by essentially adding 1/4 to 1/2 inch on each side, so my modified template is 7" across the bottom by 5" height on the bottom section. Then 3" across on the top section (again, which essentially dictates the width of the pouch when put together. With these changes to the template, I still do not get a 3.5 x 5.5 inch pouch, but at least I am closer (BTW, I think 3.5x5.5 is a tad too big IMO) Even with these small changes in the template, there is a considerable change in the appearance. The original template dimensions I think the pouch is too small. With the modified template, I question if they are too large (even if they are not 3.5x5.5). Any feedback on experience from folks who have used this write up would be greatly appreciated. Also, any thoughts on leather size? I am questioning whether or not 4-5oz shoulders is thick enough as opposed to going the next size up at 6-7oz. If the price is the same for either, would you go with the 4-5 or the 6-7? Thanks. J.
  11. Hello folks, my name is J. and my ANH Tusken was recently approved and now I am a new official member of the 501st, Imperial Sands Garrison. Ecstatic to finally be a member instead of an outsider, and looking forward to trooping more and meeting more of you Krayt Clan members that happen to troop in SoCal. Now, if I can just get my hands on at least one Krayt Clan Detachment patch, I'll be set
×